Nils Wallménius | 909b946 | 2007-03-03 00:07:31 +0000 | [diff] [blame] | 1 | % $Id$ % |
| 2 | \section{\label{ref:Recording}Recording} |
| 3 | \subsection{\label{ref:while_recording_screen}While Recording Screen} |
| 4 | \screenshot{main_menu/images/ss-while-recording-screen}{The while recording |
| 5 | screen}{} |
| 6 | |
| 7 | Entering the \setting{Recording} option in the \setting{Main Menu} brings up |
| 8 | a screen in which you can choose to enter the \setting{Recording Screen} or |
| 9 | the \setting{Recording Settings} (see below). The \setting{Recording Screen} |
| 10 | shows the time elapsed and the size of the file being recorded. A peak meter |
| 11 | is present to allow you set gain correctly. There is also a volume setting, |
| 12 | this will only affect the output level of the \dap{} and does \emph{not} |
Peter D'Hoye | 12f466d | 2007-08-26 10:44:52 +0000 | [diff] [blame] | 13 | affect the recorded sound. If enabled in the peak meter settings, a counter in |
| 14 | front of the peak meters shows the number of times the clip indicator was |
| 15 | activated during recording. The counter is reset to zero when starting a new |
| 16 | recording. |
Nils Wallménius | 909b946 | 2007-03-03 00:07:31 +0000 | [diff] [blame] | 17 | \opt{SWCODEC}{ |
| 18 | \note{When you start a recording, the hard disk will spin up. This will cause |
| 19 | the peak meters to freeze in the process. This is expected behaviour, and |
| 20 | nothing to worry about. The recording continues during the spin up.}} |
| 21 | \opt{MASCODEC}{The frequency, channels and quality} |
| 22 | \opt{SWCODEC}{The frequency and channels} settings are shown on the last line. |
| 23 | |
| 24 | The controls for this screen are: |
| 25 | \begin{table} |
| 26 | \begin{btnmap}{}{} |
| 27 | |
| 28 | \ActionStdPrev{} / \ActionStdNext & Select setting.\\ |
| 29 | % |
| 30 | \ActionSettingsDec{} / \ActionSettingsInc & Adjust selected setting.\\ |
| 31 | % |
| 32 | \ActionRecPause & Start recording.\\ |
| 33 | & While recording: pause recording (press again to |
| 34 | continue).\\ |
| 35 | % |
| 36 | \ActionRecExit & Exit \setting{Recording Screen}.\\ |
| 37 | & While recording: Stop recording.\\ |
| 38 | % |
| 39 | \opt{IRIVER_H100_PAD,IRIVER_H300_PAD,IAUDIO_X5_PAD}{ |
| 40 | \ActionRecNewfile & Starts recording.\\ |
| 41 | & While recording: close the current file and open |
| 42 | a new one.\\ |
| 43 | } |
| 44 | % |
| 45 | \ActionRecMenu & Open \setting{Recording Settings} (see below).\\ |
| 46 | % |
| 47 | \opt{RECORDER_PAD}{ |
| 48 | \ActionRecFTwo & Quick menu for recording settings. A quick press will |
| 49 | leave the screen up (press \ActionRecFTwo{} again to exit), while holding |
| 50 | it will close the screen when you release it.\\ |
| 51 | } |
| 52 | % |
| 53 | \opt{RECORDER_PAD}{ |
| 54 | \ActionRecFThree & Quick menu for source setting.\\ |
| 55 | & Quick/hold works as for \ActionRecFTwo.\\ |
| 56 | & While recording: Start a new recording file.\\ |
| 57 | } |
| 58 | \end{btnmap} |
| 59 | \end{table} |